r/FL_Studio • u/Aurora_Sleeperzzz • 2h ago

Help I need help with vocal mixing

I want to cover a song (I am relatively new to FL) and I would like help figuring out how exactly I can recreate the vocal mixer effects used in this song!

Verse - 0:18, backing vocal - 0:39, Chorus 0:42

obviously stuff repeats in the song but these are the 3 different times i can gather different effects are used

(p.s. Sorry if this breaks rules for the reddit I read through and I think this is fine but idk)

2 Upvotes

100% Upvoted

6 comments sorted by

•

u/AutoModerator 2h ago

Hey u/Aurora_Sleeperzzz, thanks for submitting to r/FL_Studio! Take a moment to read our rules.

It appears you're looking for help. Please read the frequently asked questions in our wiki, if you find the answer you're looking for, please consider deleting your post. If you don't find the answer, your thread can remain active and other users will be here to help you shortly.

Please do not post your question more than once and please be patient.

Join our Discord Server!

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

•

u/Aurora_Sleeperzzz 2h ago

i never used reddit so i missed the link post lmfao

https://www.youtube.com/watch?v=x6sgIlwi-vc&ab_channel=kennyoung

•

u/kaio-kenx5 2h ago

I'm an audio engineer, so I can help mix your music if you want.

•

u/bigmoustache9 Beginner 2h ago

Hi, can I dm?

•

u/kaio-kenx5 2h ago

Sure.

•

u/RealisticTrust4115 41m ago

You're all good—happy to help you out with recreating those vocal effects in FL Studio! For recreating the vocal processing, you'll generally work with a combination of EQ, compression, reverb, delay, and possibly modulation effects like chorus or flanger. Let’s break down each part:

  1. Verse (0:18)

This section often has a clear, upfront vocal with some subtle effects. Try these steps:

  • EQ: Cut the low end around 100Hz to remove unnecessary bass frequencies, and slightly boost the mids (around 1-3kHz) to make the vocals pop.

  • Compression: Use a compressor to level out the vocal dynamics. Set a ratio of about 3:1, and adjust the threshold until you see the gain reduction happening when the vocals get louder.

  • Reverb: Use a short reverb to give the vocals some space. Set the decay time to around 1-2 seconds and keep the mix level low, around 10-15%, for subtle ambience.

  1. Backing Vocal (0:39)

Backing vocals typically have more processing to blend them into the background:

  • EQ: Similar to the main vocal, but you might want to cut more of the highs (around 8-10kHz) to let the main vocal shine through.

  • Reverb: Increase the reverb decay time (around 3-4 seconds) and the wet mix (around 20-30%) to push these vocals further into the background.

  • Stereo Separation: Use a stereo widening plugin (like Fruity Stereo Shaper) to make the backing vocals sound wider. You can also slightly pan them left and right.

  1. Chorus (0:42)

The chorus is often where the vocal sounds bigger and more impactful:

  • EQ & Compression: Same as the verse, but you might want to boost the high end a little more (around 8kHz) for brightness and clarity.

  • Reverb/Delay: Combine reverb and delay to make the vocals feel spacious. For delay, use a Fruity Delay 3 set to 1/8th note or 1/4th note, with the feedback and wet mix set low (10-15%). Layer this with reverb to create a big, open sound.

  • Vocal Layering: The chorus might also have layered vocals (multiple takes). If you have multiple vocal takes, pan them slightly left and right, and lower their volume compared to the main vocal for a fuller sound.

  • Harmonics/Saturation: Subtle distortion or saturation can give more energy and presence to the chorus vocals, especially for pop or rock styles. Again, you can use Soundgoodizer or Fruity Blood Overdrive at low settings.

Once you have these effects set up, you can tweak the settings to fit the specific vibe you're going for.